Search found 10 matches
- Thu Sep 06, 2007 8:41 am
- Forum: Technical Support
- Topic: MDLS pinout needed
- Replies: 2
- Views: 8392
Re: MDLS pinout needed
In view of the water temp problem, could you also provide maker/part number for a water temp sender (for Zetec) compatible with MDLS ? can anybody please provide me with a pinout list or diagram for an MDLS (eprom rev G1.16)?? I have an indication of an engine temp of 125C on the EC readout (when en...
- Thu Sep 06, 2007 3:25 am
- Forum: Technical Support
- Topic: MDLS pinout needed
- Replies: 2
- Views: 8392
MDLS pinout needed
can anybody please provide me with a pinout list or diagram for an MDLS (eprom rev G1.16)?? I have an indication of an engine temp of 125C on the EC readout (when engine off or running) and I need to fault find the circuit. Also, I would really like to get some manufacturers part numbers for an air ...
- Thu Sep 06, 2007 3:18 am
- Forum: Technical Support
- Topic: PC - ECU comms problem
- Replies: 11
- Views: 22261
This post is to provide feedback and to close this thread. After receiving very detailed information from Richard, I found two problems: (i) there were crossed conductors in the comms cable (ECU TX and RX crossed) and (ii) There are wide variations in USB-Serial convertors. I tried 4 before finding ...
- Tue Sep 04, 2007 6:59 pm
- Forum: Technical Support
- Topic: PC - ECU comms problem
- Replies: 11
- Views: 22261
- Mon Sep 03, 2007 5:12 pm
- Forum: Technical Support
- Topic: PC - ECU comms problem
- Replies: 11
- Views: 22261
- Mon Sep 03, 2007 6:09 am
- Forum: Technical Support
- Topic: PC - ECU comms problem
- Replies: 11
- Views: 22261
Well, still waiting for GEMS to give some sort of contact or advice on this issue. Now missing trackdays and getting disillusioned with the whole thing. I really would appreciate some support for the expensive software I have bought, other than promises. Is there anybody out there who have experienc...
- Tue Aug 28, 2007 5:49 pm
- Forum: Technical Support
- Topic: PC - ECU comms problem
- Replies: 11
- Views: 22261
- Sun Aug 26, 2007 8:43 am
- Forum: Technical Support
- Topic: PC - ECU comms problem
- Replies: 11
- Views: 22261
Unfortunately I am still trying to resolve this comms problem, I have even gone and looked for laptops which still have serial connectors...apparently they don't exist anymore!!..so that was no good. So, having re-re-checked the ground (<0.2 Ohm) and the Baud rate (9600) several times I am still una...
- Fri Aug 24, 2007 4:20 pm
- Forum: Technical Support
- Topic: PC - ECU comms problem
- Replies: 11
- Views: 22261
PC-ECU Comms problem
Phil
I can confirm the Baud rate is set to 9600
(software uses Auto mode for scanning ECU)
Ground is OK
I have tried both 'wake up' and 'connect' modes but still the same result.
The test box says 'ECU offline' and a red flashing box at the bottom left of the screen says 'ECU Offline'.
I can confirm the Baud rate is set to 9600
(software uses Auto mode for scanning ECU)
Ground is OK
I have tried both 'wake up' and 'connect' modes but still the same result.
The test box says 'ECU offline' and a red flashing box at the bottom left of the screen says 'ECU Offline'.
- Fri Aug 24, 2007 2:47 am
- Forum: Technical Support
- Topic: PC - ECU comms problem
- Replies: 11
- Views: 22261
PC - ECU comms problem
i am trying to connect to a MDLS v1.16 using a USB serial connector. All I am getting is "ECU offline".
I am getting signal level voltage on the harness conector and at the serial connector. THe port allocation is OK.
Any suggestions???
Kiwi
I am getting signal level voltage on the harness conector and at the serial connector. THe port allocation is OK.
Any suggestions???
Kiwi